✔ All membrane systems – TPO, EPDM, PVC
✔ No upselling – honest assessment
✔ Most repairs: $300-$1,200
✔ Emergency service – commercial & residential
✔ Duro-Last Elite Contractor – 30-year warranties

✔ Emergency flat roof repair for leaks, ponding, and storm damage
✔ Expert membrane repair for TPO, EPDM, modified bitumen, and built-up systems
✔ Fast local service in neighborhoods like Hyde Park, Carrollwood, and Seminole Heights
✔ Free estimates with a full assessment of drainage, leaks, and membrane condition
✔ Licensed and insured Tampa roofing contractor compliant with Florida Building Code (License #CCC1332569)

✔ Fast emergency response for Tampa zip codes including 33602, 33603, 33604, 33612, 33613, 33618
✔ Owens Corning Preferred Contractor and Duro-Last Elite Contractor
✔ A+ BBB Rating and 40+ years of combined roofing experience
✔ Full compliance with Florida roof insurance claim protocols
✔ Service-Disabled Veteran-Owned Small Business (SDVOSB)
✔ In-house crew – no subcontracting
✔ Serving both residential and light commercial roofs

Safety First: All repairs are performed under Florida Building Code standards. We secure every worksite, follow manufacturer installation protocols, and maintain controlled access to ensure warranty protection and property safety.

» Ponding Water After Rain

Standing water on your flat roof indicates drainage failure and threatens membrane integrity. Blocked scuppers, inadequate slope, or dead valleys prevent proper water flow, leading to accelerated deterioration.

If puddles remain 24-48 hours after rain, call (813) 609-5596 immediately to prevent membrane breakdown and interior leaks.

» Visible Membrane Tears or Punctures

TPO, EPDM, modified bitumen, and cap sheet systems tear during storms, from foot traffic, or UV exposure. Even small punctures allow water infiltration that spreads beneath the membrane. We patch, seal, or replace damaged sections before leaks reach your ceiling.

» Water Stains on Ceilings or Walls

Ceiling stains signal active water intrusion through membrane defects, flashing failures, or penetration leaks. Flat roof leaks often travel horizontally before dripping down, making the source hard to locate. Call (813) 609-5596 immediately – we trace the leak path and fix the source.

» Bubbling, Blistering, or Loose Membrane

Surface bubbles indicate trapped moisture or poor adhesion beneath the membrane. Blisters compromise waterproofing and accelerate system failure. We identify the cause, repair affected areas, and restore membrane integrity.

» Sagging or Soft Deck Areas

Soft spots or visible sagging indicate water-damaged decking beneath the membrane. When saturation weakens the substrate, the entire roofing system is at risk. We assess structural damage, rebuild compromised decking, and restore a sound roofing surface.

» Failed Flashing or Seam Separation

Flashing around HVAC units, vents, and roof edges fails when sealants deteriorate or fasteners loosen. Seam failures occur in EPDM, TPO, and modified bitumen systems when adhesives break down. These are the most common flat roof leak sources in Tampa.

» Cracked or Deteriorating Coating

Protective coatings break down under Florida's intense UV exposure and heat cycles. Cracked coatings expose the membrane to accelerated weathering and water penetration. We assess coating condition and apply new silicone, acrylic, or aluminum systems when needed.

Step 1: Comprehensive Roof Inspection

We begin with a thorough rooftop assessment, examining the membrane, drainage systems, flashings, penetrations, and substrate. We use moisture meters to detect hidden water damage and document all defects with photos.

Step 2: Leak Source Identification

We trace active leaks to their source, checking common failure points: seams, penetrations, flashing details, and drainage areas. Flat roof leaks often travel far from their entry point, so precise diagnostics are critical.

Step 3: Damage Documentation

We document all roof issues for warranty or insurance claim purposes, including detailed photos, measurements, and condition reports. We work directly with your insurance adjuster when storm damage is verified.

Step 4: Material Matching & Sourcing

We source matching membrane materials (TPO, EPDM, modified bitumen, built-up) and components, ensuring compatibility with your existing system. Proper material matching maintains manufacturer warranty compliance and uniform appearance.

Step 5: Expert Repair & Reinforcement

We remove and replace damaged membrane sections, reseal seams, repair or replace flashings, and address substrate damage. We reinforce adjoining areas and verify proper drainage to prevent future issues.

Step 6: Quality Verification & Documentation

Every flat roof repair ends with a documented walkthrough. We verify water flow, test repairs, provide completion photos, and ensure every component performs correctly.